avatar

矿渣 星际魔盒 折腾记(2) - 刷黑威联通 QNAP 固件分享

哎,果然是懒,继 上一篇 已经两个多月了,机器装好USB2口,刷了个MCS7后用了一段时间一直闲置了,今天天气不错拿出来再折腾一下。

先上固件包吧:

原厂MCS7固件 https://pan.dachui.co/file/星际魔盒 台湾原厂.7z

矿渣论坛黑QNAP固件 https://pan.dachui.co/file/星际魔盒-矿渣论坛.7z

​ 用迅雷下载速度更快!

​ mcs7刷机,很简单,把我的压缩包解压到FAT32格式的U盘,卸下硬盘,拔掉网线,插上 U 盘,按住 Reset 键不放,插电源,约 10 秒后松开 Reset,刷机时间约15分钟,期间会自动重启两次,刷机途中不要断电或强行重启,你看到路由里面设备上线自动获取IP后,直接打开IP就可以进入后台了。

​ mcs7没什么好玩的,建议直接刷黑威。

QNAP刷机教程:

所需工具:螺丝刀、U盘、USB2TTL,硬盘

所需软件: Xshell 或者 PuTTY、

首先是拆机接TTL线,这个就不多说了,一代线序如下

TTL插电脑,装驱动,然后右击我的电脑-管理-设备管理器-端口,记下你的TTL所在COM端口

打开 PuTTY 新建 SERIAL 会话 ,端口填上一步的COM端口,速率 115200 ,点open打开会话

连上网线,保证电脑和盒子在一个网络环境,在 PuTTY 会话中按住 Esc键不放,盒子插电。这时PuTTY 开始输出信息,当界面显示 Realtek> 时,松开Esc键。

从路由器后台确认自己电脑的IP,比如我的是 192.168.31.121,然后打开压缩包里面专用工具的 tftpd32,防火墙放行,确定IP是自己电脑的IP

putty输入命令

Code
1
2
3
4
5
6
env set ipaddr 192.168.31.66  #设定盒子IP,从路由后台查看没有设备占用就行
env set serverip 192.168.31.121 #设定FTP服务器IP
tftp 0x03000000 emmc_kernel.bin
tftp 0x01ff2000 emmc_rescue_dt.bin
tftp 0x02200000 emmc_rescue_rootfs.bin
go all #通过tftp刷底层

注意:如果输入go all盒子重启,可以在go all命令几秒钟后拔掉电源线,按住复位键插入电源线,等待15秒后松开复位键,然后可以继续操作。

把压缩包里主文件 bbs.nas66.com.img 复制到U盘,插上盒子,putty会走代码,出现 Mount sda succeeded! 时说明U盘挂载完毕,输入 df 查看U盘挂载路径,然后 cd 到这个目录,比如我的:

Code
1
2
3
4
5
6
7
/ # df
Filesystem 1K-blocks Used Available Use% Mounted on
devtmpfs 379356 0 379356 0% /dev
/dev/sda 15828992 3817504 12011488 24% /tmp/usbmounts/sda #这里是挂载路径
/ # cd /tmp/usbmounts/sda
/tmp/usbmounts/sda # ls #确认一下文件能不能识别
System Volume Information bbs.nas66.com.img

没毛病输入命令开始刷机

Code
1
cat bbs.nas66.com.img > /dev/mmcblk0

这里等待时间比较长,大概十几分钟吧,当putty出现 / # 可以输入命令时 输入 reboot 重启盒子。

重启时间也很久,当putty输出如下提示,果断打开这个IP,进入设置后台。

Code
1
2
3
Welcome to TS-228(192.168.31.14), QNAP Systems, Inc.

NAS000509 login:

注意,设置向导会检测到有新固件,点跳过!点跳过!!点跳过!!! 然后就是正常流程了,初始化需要插入硬盘。

设置完重启时间很久很久,直接看路由后台判断比较靠谱。

拔掉TTL线、装回机箱、然后就可以愉快的玩耍了

下面列上我的putty记录,可以核对一下步骤:

Code
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
?
?hb

U-Boot 2012.07 (Nov 20 2018 - 11:37:19) ver_160517

CPU : Cortex-A7 dual core
MIS_GP1DATO[1801b114] default=0x00000008 [should be 0x1801b114,0x00000008]
MIS_GP1DIR[1801b104] default=0x040000a8 [should be 0x1801b104,0x04000028]
MUXPAD3[1800036c] default=0x00155049 [should be 0x1800036c,0x10025555]
CRT_MUXPAD1[18000364] default=0x00000000 [should be 0x18000364,0x00000000]
MIS_GP0DATO[1801b110] default=0x00000000 [should be 0x1801b110,0x00000000]
MIS_GP0DIR[1801b100] default=0x00000020 [should be 0x1801b100,0x00000020]
MUXPAD4[18000370] default=0x00155249 [should be 0x18000370,0x00155249]
20170626, setGPIO(45, 1)
20160715, ft5x06_ts reset set to 1(not reset for i2c will crash)
20170626, setGPIO(46, 1)
-- hwinit.c: set gpio39(beep), 41,43(i2c2), gpio40,42(fan_low/hi), gpio47(reset USB HUB) --
reg[0x18000368]=0x00000000 0
reg[0x18000368]=0x00ee0008 0-1
Board: Realtek QA Board
DRAM: 1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 [email protected]
MMC: rtk_emmc : Detect chip rev. >= B
RTD1195 eMMC: 0
rtk_emmc : Detect chip rev. >= B
mmc->version=0x00010000
version=0x00000004
SDR select (sample/push) : 0x00/0x00
[LY] cardtype=57, mmc->card_caps=0f
[LY] TBD : to support DDR50/HS200
[LY] SDR bus width=2
SDR select (sample/push) : 0x00/0x00
[LY] mmc->boot_caps = 203
[LY] sdr50 : 0
exit from mmc_startup(),err=0
Device: RTD1195 eMMC
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Tran Speed: 31975000000000a
Rd Block Len: 512
MMC version 4.0
High Capacity: No
Capacity: 3.6 GiB
Bus Width: 8-bit
Speed: SDR50
Factory: MMC
Factory: pp:1, seq#:0x24, size:0x20e00
------------can't find tmp/factory/000BootParam.h
------------can't find tmp/factory/video_rpc.bin
tv_system=25 mode=1
----------VOUT_CONFIG_TV_SYSTEM----------
interfaceType =0x0
videoInfo.standard =0x19000000
videoInfo.enProg =0x1
videoInfo.enDIF =0x1
videoInfo.enCompRGB =0x0
videoInfo.pedType =0x1000000
videoInfo.dataInt0 =0x4000000
videoInfo.dataInt1 =0x0
hdmiInfo.hdmiMode =0x1000000
hdmiInfo.audioSampleFreq =0x3000000
hdmiInfo.audioChannelCount =0x1
hdmiInfo.dataByte1 =0x0
hdmiInfo.dataByte2 =0x0
hdmiInfo.dataByte3 =0x0
hdmiInfo.dataByte4 =0x0
hdmiInfo.dataByte5 =0x0
hdmiInfo.dataInt0 =0x1000000
-----------------------------------------
In: serial
Out: serial
Err: serial
LVDS: on
Net: Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
Hit Esc or Tab key to enter console mode or rescue linux: 0 20170626: MUXPAD3[0 x1800036c]=0x00155049, MIS_GP1DIR[0x1801b104]=0x0400e5a8, MIS_GP1DATO[0x1801b114 ]=0x0000e508

------------can't find tmp/factory/recovery

Press Esc Key

Enter console mode, disable watchdog ...(boot_mode=0)

Realtek> env set ipaddr 192.168.31.66
Realtek> env set serverip 192.168.31.121
Realtek> tftp 0x03000000 emmc_kernel.bin
TFTP from server 192.168.31.121; our IP address is 192.168.31.66
Filename 'emmc_kernel.bin'.
Load address: 0x3000000
Loading: T #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#####################################################
done
Bytes transferred = 4370944 (42b200 hex)
Realtek> tftp 0x01ff2000 emmc_rescue_dt.bin
TFTP from server 192.168.31.121; our IP address is 192.168.31.66
Filename 'emmc_rescue_dt.bin'.
Load address: 0x1ff2000
Loading: #########
done
Bytes transferred = 32768 (8000 hex)
Realtek> tftp 0x02200000 emmc_rescue_rootfs.bin
TFTP from server 192.168.31.121; our IP address is 192.168.31.66
Filename 'emmc_rescue_rootfs.bin'.
Load address: 0x2200000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########
done
Bytes transferred = 4194304 (400000 hex)
Realtek> go all
Start Audio Firmware ...
== go rtk_call_bootm() ==
bootargs=console=ttyS0,115200 earlyprintk loglevel=4 panic=2
bootm_argv ={ bootm,3000000,-,1ff2000,}
## Booting kernel from Legacy Image at 03000000 ...
Image Name: Linux-3.10.24-rtk-nas
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4331928 Bytes = 4.1 MiB
Load Address: 00108000
Entry Point: 00108000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01ff2000
Booting using the fdt blob at 0x01ff2000
Loading Kernel Image ... OK
OK
== bootm.c boot_prep_linux(): commandline=bootargs=console=ttyS0,115200 earlypri ntk loglevel=4 panic=2 root=179:01 ro rootfstype=ext4 ==
Starting kernel ...
[ 0.074958] -- driver_register(): rtk119x-gpio
[ 0.080348] -- driver_register(): rtk119x-pinctrl
[ 0.086710] -- driver_register(): dummy
[ 0.135903] -- driver_register(): Generic PHY
[ 0.141133] -- driver_register(): usbfs
[ 0.145614] -- driver_register(): hub
[ 0.149957] -- driver_register(): usb
[ 0.371143] -- driver_register(): Venus_I2C
[ 0.580751] -- driver_register(): arm-pmu
[ 0.585968] -- driver_register(): ion-rtk
[ 0.692142] -- driver_register(): Venus_RPC
[ 0.698147] -- driver_register(): rtk_rtc
[ 0.703718] -- driver_register(): rtk-fb
[ 0.709474] -- driver_register(): vl53l0x-motion-sensor-low-act
[ 0.716564] -- driver_register(): rtk119x-al-lcd-key
[ 0.722543] -- driver_register(): rtk119x-al-default-key
[ 0.728826] -- driver_register(): rtk119x-ir
[ 0.733755] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2689 no pinctrl found -19
[ 0.744354] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2815 iso_sys_reg_base = fe007000
[ 0.755378] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2816 iso_irda_reg_base = fe007400
[ 0.766506] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default irrx-prot ocol = 1 .
[ 0.775354] NOTE : NEC = 1, RC5 = 2, SHARP = 3, SONY = 4, C03 = 5, RC6 = 6, R AW_NEC = 7, RCA = 8, PANASONIC = 9, KONKA=10, RAW_RC6 = 11
[ 0.788754] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default irtx-prot ocol = 1 .
[ 0.797592] NOTE : NEC_TX = 1, RC5_TX = 2, SHARP_TX = 3, SONY_TX = 4, C 03_TX = 5, RC6_TX = 6, RCA_TX = 7, PANASONIC_TX = 8, KONKA_TX=9
[ 0.810889] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default cust_code
[ 0.818767] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default scancode_ msk
[ 0.826954] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default custcode_ msk
[ 0.835141] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default keymap ta ble rtk_mk5_tv_key_table.
[ 0.845406] [WARNING]rtk119x_ir_probe Parsing DTB fail, Use default reg-ir-dp ir = 60 .
[ 0.855456] -- driver_register(): VenusIR
[ 0.861740] -- driver_register(): VenusIRTX
[ 0.867735] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] rtk119x_ir_probe 2906 irq number = 197
[ 0.877820] Venus_IR_Init ---- begin ----
[ 0.882309] Venus_IR_Init for NEC mode
[ 0.886497] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] get reg-ir-dpir = 60ld us from dtb, regval=0x3000lx
[ 0.897609] Venus_IR_Init for NEC_TX mode
[ 0.902542] -- driver_register(): rtk_puwrap
[ 0.907781] -- driver_register(): rtk_vpu
[ 0.913223] -- driver_register(): rtk_jpu
[ 0.920031] -- driver_register(): alarmtimer
[ 0.933037] -- driver_register(): simple-framebuffer
[ 0.955792] -- driver_register(): serial8250
[ 0.961049] -- driver_register(): dw-apb-uart
[ 0.999009] -- driver_register(): sd
[ 1.004288] -- driver_register(): r8169
[ 1.009024] -- driver_register(): rtl8150
[ 1.013683] -- driver_register(): r8152
[ 1.018362] -- driver_register(): rtk119x-se
[ 1.024871] -- driver_register(): rtk_rbus
[ 1.030465] -- driver_register(): dwc3
[ 1.034726] -- driver_register(): rtk-dwc3
[ 1.040484] dwc3 18020000.dwc3: no usb2 phy configured
[ 1.047704] -- driver_register(): rtk-usb2phy
[ 1.052729] -- driver_register(): rtk-usb3phy
[ 1.057683] -- driver_register(): ehci-platform
[ 1.062797] -- driver_register(): rtk-ehci
[ 1.101010] -- driver_register(): rtk-ohci
[ 1.164892] -- driver_register(): xhci-hcd
[ 1.169512] -- driver_register(): usb-storage
[ 1.180711] -- driver_register(): rtk_hdmi
[ 1.189173] -- driver_register(): cec0
[ 1.193981] -- driver_register(): cec1
[ 1.199437] -- driver_register(): rtk119x-cpufreq
[ 1.310142] -- driver_register(): mmcblk
[ 1.314572] -- driver_register(): sdhci-rtk
[ 1.359298] -- driver_register(): rtkemmc
[ 1.400488] -- driver_register(): hid-generic
[ 1.405309] -- driver_register(): usbhid
[ 1.414847] -- driver_register(): timed-gpio
[ 1.421226] -- driver_register(): snd_alsa_rtk
[ 1.429462] -- driver_register(): snd-usb-audio
[ 1.435489] -- driver_register(): snd-soc-dummy
[ 1.440643] -- driver_register(): soc-audio
[ 1.445307] -- driver_register(): oprofile-perf
[ 1.457250] -- driver_register(): rfkill
[ 1.467329] -- driver_register(): avcpu
[ 1.953385] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Sun Dec 1 00:00:00 UTC 2013
/ # [ 2.128026] hub 3-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 2.247872] usb 3-1: == new high-speed USB device number 2 using xhci-hcd BEG [udev.idVendor=0x0000, idProduct=0x0000]
[ 2.302519] usb 3-1: == new high-speed USB device number 2 using xhci-hcd END [udev.idVendor=0x174c, idProduct=0x2074, hdev.idVendor=0x1d6b, idProduct=0x0002 , product=xHCI Host Controller, manufacturer=Linux 3.10.24-rtk-nas xhci-hcd, ser ial=xhci-hcd.2.auto]
[ 2.390557] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 2.507769] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 2.528614] usb 4-1: == new super-speed USB device number 2 using xhci-hcd EN D [udev.idVendor=0x174c, idProduct=0x3074, hdev.idVendor=0x1d6b, idProduct=0x000 3, product=xHCI Host Controller, manufacturer=Linux 3.10.24-rtk-nas xhci-hcd, se rial=xhci-hcd.2.auto]
[ 6.853275] prepare to U0
[ 6.873224] U0
[ 6.875015] usb 3-1: retry with reset-resume
[ 7.023871] usb 3-1: == reset high-speed USB device number 2 using xhci-hcd B EG [udev.idVendor=0x174c, idProduct=0x2074]
[ 7.077772] usb 3-1: == reset high-speed USB device number 2 using xhci-hcd E ND [udev.idVendor=0x174c, idProduct=0x2074, hdev.idVendor=0x1d6b, idProduct=0x00 02, product=xHCI Host Controller, manufacturer=Linux 3.10.24-rtk-nas xhci-hcd, s erial=xhci-hcd.2.auto]
[ 7.362755] hub 3-0:1.0: port 1, status 0503, change 0004, 480 Mb/s
[ 7.383940] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 7.390542] hub 3-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 7.492745] usb 3-1.4: == new high-speed USB device number 3 using xhci-hcd B EG [udev.idVendor=0x0000, idProduct=0x0000]
[ 7.522968] usb 3-1.4: == new high-speed USB device number 3 using xhci-hcd E ND [udev.idVendor=0x03f0, idProduct=0xe607, hdev.idVendor=0x174c, idProduct=0x20 74, product=AS2107, manufacturer=ASMedia, serial=USB2.0 Hub]
[ 7.682422] usb 3-1.4: hub_port_connect_change unbind-probe dev_name = 3-1.4 jiffies= 0x301
[ 12.719074] hub 4-1:1.0: warm reset port 1
[ 12.838933] hub 4-1:1.0: warm reset port 2
[ 14.122304] sd 1:0:0:0: [sda] No Caching mode page found
[ 14.127849] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 14.146746] sd 1:0:0:0: [sda] No Caching mode page found
[ 14.152208] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 14.176243] sd 1:0:0:0: [sda] No Caching mode page found
[ 14.181702] sd 1:0:0:0: [sda] Assuming drive cache: write through
[nas-hotplug] Mount sda succeeded!

/ # df
Filesystem 1K-blocks Used Available Use% Mounted on
devtmpfs 379356 0 379356 0% /dev
/dev/sda 15828992 3817504 12011488 24% /tmp/usbmounts/sda
/ # cd /tmp/usbmounts/sda
/tmp/usbmounts/sda # ls
System Volume Information bbs.nas66.com.img
/tmp/usbmounts/sda # cat bbs.nas66.com.img > /dev/mmcblk0
/tmp/usbmounts/sda # reboot
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes[ 1153.531773] sdio_reset_fun...
[ 1153.534819] Stop emmc...
[ 1153.537945] Do watchdog reset directly...

?hb

U-Boot 2012.07 (Jan 27 2016 - 17:16:49)

CPU : Cortex-A7 dual core
Board: Realtek Demo Board
DRAM: 1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 [email protected]
MMC: rtk_emmc : Detect chip rev. >= B
RTD1195 eMMC: 0
rtk_emmc : Detect chip rev. >= B
mmc->version=0x00010000
version=0x00000004
SDR select (sample/push) : 0x00/0x00
[LY] cardtype=57, mmc->card_caps=0f
[LY] TBD : to support DDR50/HS200
[LY] SDR bus width=2
SDR select (sample/push) : 0x00/0x00
[LY] mmc->boot_caps = 203
[LY] sdr50 : 0
exit from mmc_startup(),err=0
Device: RTD1195 eMMC
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Tran Speed: 31975000000000a
Rd Block Len: 512
MMC version 4.0
High Capacity: No
Capacity: 3.6 GiB
Bus Width: 8-bit
Speed: SDR50
Factory: MMC
Factory: pp:1, seq#:0x130, size:0x21600
get_bootparam:
------------can't find tmp/factory/000BootParam.h
Factory RO: MMC
[FAC_RO] No factory_ro data in eMMC
In: serial
Out: serial
Err: serial
Net: Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
Hit Esc or Tab key to enter console mode or rescue linux: 0
------------can't find tmp/factory/recovery
======== Checking into android recovery ====

Start Boot Setup ...
[INFO] fw desc table base: 0x00620000, count: 6
Normal boot fw follow...
Kernel:
FW Image to 0x03000000, size=0x0058bbd0, 0x2c5e blocks (0x0358bbd0)
FW Image fr 0x008b7600, fr block 0x45bb (non-lzma)
DT:
FW Image to 0x01ff2000, size=0x000064fa, 0x33 blocks (0x01ff84fa)
FW Image fr 0x00630000, fr block 0x3180 (non-lzma)
resolution = <0x500 0x2d0>
ROOTFS:
FW Image to 0x02200000, size=0x00400000, 0x2000 blocks (0x02600000)
FW Image fr 0x01a43200, fr block 0xd219 (non-lzma)
Audio FW:
FW Image to 0x01b00000, size=0x0027f528, 0x13fb blocks (0x01d7f528)
FW Image fr 0x00638000, fr block 0x31c0 (non-lzma)
Start A/V Firmware ...
L# Booting kernel from
: gHacDy MIIma geR aatw 0 3E00n00a0b0 l..e.
MP GI mACag3e D TNaSme M:P E GLi2nu xA-3A.1C0. 20D-aDlP-2 .5W.3M
peP RImOa MgeL PTy
:
C SARPM DLiInFux KReranwel IEmnagae b(luneco:m pMPreGss edA)
B3 DDTaSta M SPiEzeG:2 AA58C1 51D84D BPy WteMsA =P R5O. M5L MP i


LFoaodr Acdder es2s:c h00 10F8o00r0m
a t: EnDTtrSy PoDinTt:S H 0D0 10A80C003
. DD PV eMLriPf yAAinCg WMChAecPkRsuOm ..



[AO][InitHDMIVideoType]HDMI Frequecny 148, resolution 25


@@@@@@@One Step TV System magic number = 0xc0de0bee, addr = [email protected]@@@@@@

@@@@@@No hdmi mode
HDMIOff = 1
[VO_SetVideoStandard]st 25 p 1 1 0
[VO_SetVideoStandard]ped 1 data0 0x00000004 data1 0x00000000
[VO_SetVideoStandard]st 25 p 1 1 0
[VO_SetVideoStandard]ped 1 data0 0x00000004 data1 0x00000000
inten.i 0 hdmi 0
[VO setTVStandard 25 3D 0 0]

(TVE) TVE_DAC_mode 0,,cmd->enProg 1!! ~~comp 1, ch2 0, mode_3D 0!!
~~TVE standard#
OK
## Flattened Device Tree blob at 01ff2000
Booting using the fdt blob at 0x01ff2000
Loading Kernel Image ... OK
OK
Starting kernel ...
SetVideoStandard return!

(VO_ConfigHDMI_InfoFrame) L:232, is_hdmi_plugin 0, hdmiMode 2!!Mode 2 dataByte1 0x000000d8 0x000000dd 0x00000028
dataByte4 0x00000081 0x000000b5 int0 0x81d853c4
Mode 2 dataByte1 0x000000d8 0x000000dd 0x00000028
dataByte4 0x00000081 0x000000b5 int0 0x81d853c4
fw turn off 0xb800d044 = 0x00000000!
boot_info 0xa0000000 magic 0xffffffff en 255
[AO]check 0x 0x180056e4, HDMI Mode?(0)
[ 1.100919] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.110598] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.120594] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.160883] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.170584] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.180581] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 1.717952] [arch/arm/mach-rtk119x/driver/irda/venus_ir.c] get reg-ir-dpir = 50ld us from dtb, regval=0x2500lx
[ROS: openRPC() intr_scpu_dev_r buf 0x00e2ffa1 s 0x00e2ffa1 e 0x00e4ffa1 i 0 x00e2ffa1[ROS: openStubRPC() intr_scpu_dev_w buf 0x00e6ffa1 s 0x00e6ffa1 e 0x 00e8ffa1 i[AVCPU] Set Debug level 0x00000001
-------------------
Audio Version = 890778 (phoenix)
Common Version = 0
Binary src compiled at Dec 14 2015 10:26:11
Note =
-------------------




[A] gloabl malloc size 0x003ffeb8
[ 1.792546] AudioIntrRead:141 can't find process for handling AudioIntrRead p rogramID:98
[ 1.801612] AudioIntrRead: program:98 version:0 procedure:1 taskID:0 sysTID:4 294967295 sysPID:4294967295 size:4 context:81d8d5d5 atomic
[ 2.026510] dwc3 18020000.dwc3: no usb2 phy configured
[ 3.421252] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 3.920731] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 4.420232] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 4.919731] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 6.777888] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 7.277372] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 7.776871] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 8.276371] [drivers/i2c/busses/i2c-phoenix-priv.c] venus_i2c_bus_jam_recover 1416 end
[ 8.835728] rtc-rx8010 3-0032: Unable to write register #23
[ 8.841436] i2c i2c-3: probing for rx8010 failed
[ 8.852036] cpufreq: Failed to obtain VDDARM: -517
[ 8.856960] cpufreq: Only frequency scaling available
[ 8.994790] cpufreq: Failed to obtain VDDARM: -517
[ 8.999711] cpufreq: Only frequency scaling available
[ 9.065550] ilitek_init,996,ilitek.dev.remove_flag =0
[ 9.415103] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
resize2fs 1.42.9 (28-Dec-2013)
The filesystem is already 89598 blocks long. Nothing to do!

resize2fs 1.42.9 (28-Dec-2013)
The filesystem is already 20472 blocks long. Nothing to do!

[ 9.584954] hub 3-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 9.704795] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 9.812318] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 9.934710] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 10.004709] hub 3-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 10.104514] usb 3-1.4: new high-speed USB device number 3 using xhci-hcd
[ 10.274206] usb 3-1.4: hub_port_connect_change unbind-probe dev_name = 3-1.4 jiffies= 0x404
initramfs_qnap.cpio.gz: OK
md5sum check OK!
[ 11.326007] sd 1:0:0:0: [sda] No Caching mode page found
[ 11.331451] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 11.339551] sd 1:0:0:0: [sda] No Caching mode page found
[ 11.345072] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 11.353795] sd 1:0:0:0: [sda] No Caching mode page found
[ 11.359238] sd 1:0:0:0: [sda] Assuming drive cache: write through
unzip initramfs_qnap.cpio.gz Success!
49442 blocks
extract initramfs_qnap.cpio Success!
Untar /mnt/emmcp5/mnt/boot_disk/boot/rootfs2.tgz success
rootfs_tas.tgz: OK
rootfs_tas.tgz - md5sum check OK!
Untar rootfs_tas.tgz success
resize2fs 1.42.13 (17-May-2015)
The filesystem is already 15352 (1k) blocks long. Nothing to do!

[ 35.916985] fnotify: Launch the fnotify thread: 4006111424
[ 43.612972] r8169 18016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 43.621887] r8169 18016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
^A[ 47.299090] r8169 18016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay : 10).
[ 47.308027] r8169 18016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
[ 70.855536] r8169 18016000.gmac eth0: rtl_csiar_cond == 0 (loop: 100, delay: 10).
[ 70.864480] r8169 18016000.gmac eth0: rtl_csiar_cond == 1 (loop: 100, delay: 10).
upnpd[3763]: UPnP SDK Successfully Initialized.
upnpd[3763]: Succesfully set the Web Server Root Directory.
upnpd[3763]: IGD root device successfully registered.
upnpd[3763]: Advertisements Sent. Listening for requests ...
upnpd[3959]: UPnP SDK Successfully Initialized.
upnpd[3959]: Succesfully set the Web Server Root Directory.
upnpd[3959]: IGD root device successfully registered.
upnpd[3959]: Advertisements Sent. Listening for requests ...
[ 107.997407] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 108.004199] hub 4-1:1.0: warm reset port 1
[ 108.127959] hub 4-1:1.0: warm reset port 2
daemon_mgr PID 4491/4490
[ 112.428581] hub 4-1:1.0: warm reset port 1
[ 112.553409] hub 4-1:1.0: warm reset port 2


Welcome to TS-228(192.168.31.14), QNAP Systems, Inc.

NAS000509 login:
文章作者: DaChui
文章链接: https://dachui.co/p/5.html
版权声明: 本博客所有文章除特别声明外,均采用 CC BY-NC-SA 4.0 许可协议。转载请注明来自 大锤的博客

评论